Apollo

Apollo XP95 Optical Smoke Detector DILL switchFully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Works using the light scatter principle.Responds well to slow-burning, smouldering fires.Well-suited for bedrooms and escape routes.Red LED illuminates when..

Isolator for addressable systemsThe Isolator is placed at intervals on the loop and ensures that, in the case of a short circuit, only the section between the isolators will be affected. When the short-circuit is removed, the isolators automatically restore power and data to the isolated sec..

XP95 red manual addressable call point  Fully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire PanelsВith built-in 20 devices isolator;ResettableCertified to EN 54-11 EN 54-17..

Apollo Waterproof Manual Call Point with IsolatorFully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire PanelsВith built-in 20 devices isolator;ResettableCertified to ЕN 54-11 EN 54-17..

Apollo XP95 Standard Temperature Detector DILL switchA high quality Type A2S standard temperature (55°C) heat detector Fully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Monitors temperature by using a single thermistor which provides a voltage out..

Isolator Base..

Apollo XP95 High Temperature Detector DILL switchA high quality Type CS high temperature (90°C) heat detector Fully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Monitors temperature by using a single thermistor which provides a voltage output propo..

Apollo XP95 I.S. Manual Call PointXP95 Intrinsically Safe (IS) detectors are a development of the well established analogue addressable XP95 range from Apollo. XP95 IS detectors feature all the benefits of the standard range, but are developed specifically for use in hazardous areas.Resettable..

The duct smoke detector is supplied as a housing with a base fitted for either a conventional detector or an analogue addressable detector. The housing has provision for electrical connections depending on the type of detector fitted. For technical data on the detector head, please refer to the ..

 Common base for the Series S65  and the DiL Switch Apollo  detectors..

The Intelligent Switch Monitor is designed to monitor the state of one or more single pole, volt-free contacts connected on a single pair of cables to report the status. It has a selectable status reporting delay making it suitable for monitoring flow switches...

XP95 I.S. Manual Call Point MEDC StyleXP95 Intrinsically Safe (IS) detectors are a development of the well established analogue addressable XP95 range from Apollo. This manual fire alarm call point has been designed for use in flammable atmospheres and harsh environmental conditions. The GRP enc..

  Relay base for the Series S65  and the DiL Switch Apollo  detectors..

The Intelligent Twin Switch Monitor provides the function of two Switch Monitor units within one enclosure. The two units are electrically independent of each other. There is a DIL switch on each unit to set the address.Both Switch Monitor units in the enclosure are designed to monitor the..

Negative switching Isolating base for the Apollo DiL Switch detectors..

Apollo XP95 Optical Smoke DetectorFully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Works using the light scatter principle.Responds well to slow-burning, smouldering fires.Well-suited for bedrooms and escape routes.Red LED illuminates when the detecto..

The Zone Monitor powers and controls the operation of a zone of up to 20 Apollo Series 65 or Orbis Fire Detectors from a Discovery or XP95 loop...

Apollo XP95 Standard Temperature DetectorA high quality Type A2S standard temperature (55°C) heat detector Fully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Monitors temperature by using a single thermistor which provides a voltage output proporti..

The Intelligent Mains Switching Input/Output Unit provides a single line tolerant circuit (CoreProtocol only) containing one or more normally open contacts connected to a single pair of cables. It also provides a voltage free change over relay output capable of switching mains...

Apollo XP95 High Temperature Detector A high quality Type CS high temperature (90°C) heat detector Fully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Monitors temperature by using a single thermistor which provides a voltage output proportional to ..

The Input/Output Unit provides a voltage-free, double pole changeover (DPCO) relay output, a single monitored switch input and an unmonitored, non-polarised opto-coupled input.Three visible LEDsLoop-poweredCapable of switching up to 30V at 1ABuilt-in isolator..

Apollo XP95 Multisensor DetectorFully compatible with C-TEC's XFP & ZFP XP95/Discovery Addressable Fire Panels.Combines an optical smoke sensor and thermistor temperature sensor A1RResponds well to a wide range of fires.Well suited for environments such as hotel bedrooms.Red LED i..

 Common base for the Apollo XP95 detectors..

The Sounder Control Unit is used to control the operation of a zone of conventional sounders and report their status to the control panel...

The DIN-Rail Sounder Controller (5 Amperes) is used to control the operation of a zone of externally powered sounders and report their status to the control panel...

Negative switching Isolating base for the Apollo XP95 detectors..

Pre-Addressed XPERT Cards are supplied with pips already removed from 1 to 126..